EAA Builders Log Website
EMail address:
Password:
- Lost my password
close
EAA Builders Log
(An EAA website).
Help
Contact Us
About
Sign Up
Login
Project:
wlawrence
-
Listing of Entries
(Please mouse-over any icon to get a description of that function).
Categories
Show All Entries
- (407)
Introduction
- (1)
Avionics
- (8)
Baffling
- (12)
Canopy
- (40)
Controls
- (15)
Cowl
- (32)
Dialogue
- (3)
Documentation
- (5)
Empennage
- (1)
Engine
- (95)
-
Ignition bracket
-
Engine run, starting...
-
More trials
-
Another engine run
-
Engine Start
-
Rocker Shaft Upgrade
-
Baffling lily gilding
-
More with the baffles
-
Baffling
-
New magnetron is in
-
Breather mods for a...
-
Top of the engine
-
Push rod tubes
-
Heads
-
Insulating the exhaust
-
Test Alternator Output
-
Fabricate New Valve...
-
Clean Oil Breather Tube
-
Complete Engine Wiring
-
Reinstall Engine...
-
Engine Oil Filler Cap
-
Replace Motor Mount...
-
Install New Oil...
-
Successful Engine Run
-
Install New Throttle...
-
Recheck Oil Pressure...
-
Remove, Inspect,...
-
Start Engine Check...
-
Install New Oil...
-
Remove Oil Cooler
-
Continue Engine...
-
Diagnose And Remove...
-
Continue Engine...
-
Shorten Oil Cooler...
-
Made and Installed...
-
Made and Installed...
-
Remove Oil Cooler...
-
Improve Engine...
-
Engine Oil Pressure...
-
Fill Engine...
-
Safety Wire...
-
Reinstall Exhaust...
-
Weld Stainess Steel...
-
Locate and Mark TDC...
-
Plug Spark Plug Wire...
-
Continue Engine...
-
Reposition CHT...
-
Secure Cylinder Head...
-
Shorten Oil Cooler...
-
Engine and Oil...
-
Continue Engine Oil...
-
Continue Engine...
-
Continue Engine Oil...
-
Continue Engine...
-
Continue Engine...
-
Continue Engine...
-
Continue Engine...
-
Complete and Install...
-
Cut Seals for Rear...
-
Fabricate Bracket to...
-
Engine Oil Cooler...
-
Begin Cutting and...
-
Elininate...
-
Reassemble Engine...
-
Form and Install...
-
Fabricate Starter...
-
Cutting Access Holes...
-
Fabricate and...
-
Continue Fabrication...
-
Install Carburetor...
-
Install Oil Cooler...
-
Engine Cooling...
-
Mount Oill Cooler to...
-
Lower Engine Case...
-
Engine Cooling...
-
Continue Fabrication...
-
Throttle Cable...
-
Throttle and Mixture...
-
Shorten Intake...
-
Install Missing...
-
Re-route Mixture Cable
-
Cut Patterns For...
-
Prepare To Cut Holes...
-
Continued Progress...
-
Continued Progress...
-
Engine Wiring and...
-
Hub Spacer
-
Exhaust System
-
Install 20 AMP...
-
Engine Returns
-
Engine work complete.
-
Engine work begins
-
Transport Engine
-
Remove Engine
-
Removing Old...
Firewall
- (2)
Fuel System
- (27)
Fuselage
- (19)
Glare Shield
- (5)
Inspection
- (1)
Instrument Panel
- (18)
Interior Finish
- (5)
Landing Gear
- (11)
Lighting
Paint / Decals
- (1)
Presentation
- (1)
Project Sale
- (1)
Propeller
- (2)
Research
- (1)
Tail Feathers
Tools
- (1)
Various
- (13)
Windscreen
- (16)
Wings
- (34)
Workshop
- (9)
Ignition
- (28)
Builder Name:
William Lawrence
-
Project:
Sonex
-
VIEW REPORTS
Total Hours:
1884.3
Total Flight Time:
Start/Last Date:
Nov 21, 2018 - No Finish Date
Engine:
Aerovee
Friendly URL:
https://eaabuilderslog.org?s=wlawrence
Home or Last Project Picture
Nov 29, 2020
Install Oil Cooler and Baffle Assembly to Lower Engine Case
- (9 hours)
Category: Engine
Frank Kelly and Bill Lawrence, after determining that the new narrower and thicker oil cooler did not provide adequate clearance with lower engine case, reverted to using original wider and thinner oil cooler, attached it to the oil cooler baffle and installed it on the lower engine case. Harvard worked on the windscreen bow.
Frank_FittingOilCoolerBaffle_LeeHarvard_WorkingOnScrewsForWindscreen
Bill_AdjustingOilCoolerBaffle
LeeHarvard_WorkingOnScrewsForWindscreen_BillFrank_InstallingOilCoolerBaffle
LeeHarvard_WorkingOnScrewsForWindscreen_BillFrank_InstallingOilCoolerBaffle_s_5741.jpg
Tray from low and fwd
Tray from fwd
NOTE: This information is strictly used for the EAA Builders Log project within the
EAA organization
.
-
Policy
-
© Copyright 2024 Brevard Web Pro, Inc.